未分类

08/08/202408/08/2024

Installation and commissioning of drilling cuttings dryer

Drilling cuttings dryer is mainly used for drilling fluid recovery in drilling cuttings, recycling drilling fluid with reuse value in cuttings, reducing the cost of drilling fluid in the drilling process, and meeting the transportation and environmental standards of drilling cuttings. The first use of the drill chip dryer needs to pay attention to the installation and debugging methods so that the equipment can operate safely and stably.

During the installation process, we must first ensure the safety of lifting and check whether all the lifting points of the equipment are firm and safe. When installing, ensure that the installation table is clean and tidy to prevent debris on the installation table from affecting the installation. To ensure the safety of the equipment during transportation, special transportation protection devices are installed, which must be removed after installation to prevent damage to the dryer, and then install all the pipelines, and the electric control system of the dryer, be sure to carefully read the electric control operating instructions before the installation of the electric control system.

After the installation of all the relevant equipment, you can start debugging, before starting, be sure to check the integrity of the installation of the equipment, whether there is leakage or installation. Check whether transportation protection devices are removed. Turn the motor pulley by hand to see if there is any abnormal situation such as congestion and check whether the belt is damaged and whether the tightness is appropriate, but check whether the oil level of the tank is appropriate, and check whether all the pipelines are connected, and check whether all the electric control system is connected in place.

After the boot check, you can click the oil pump motor to check whether the motor rotation direction is correct, the motor is clockwise rotation if not correct, timely adjustment; Point the main motor, and observe whether the rotation direction of the distribution disk is correct, and observe whether there are other abnormal conditions, from the top down, the rotation direction should be clockwise rotation; Move the feed pump, observe whether the rotation direction of the feed pump is correct, and check that the above items have no problems, you can start the equipment for debugging production.

07/03/202407/03/2024

KOSUN Vertical Cuttings Dryer – application introduction

The cuttings dryer is designed to reduce the operator’s total drilling fluid cost and limit the amount of waste handled. Recover drilling fluid directly from cuttings and weight mud from shaker mesh to avoid loss of weight mud due to shaker failure, rig movement, or screen blockage. The centrifuge helps meet certain cuttings liquid discharge requirements that must be complied with. The cuttings dryer is a continuous screen centrifuge with automatic feed control for solid-liquid separation. The cuttings dryer is designed to recover the liquid phase drilling fluid from the cuttings by applying a high centrifugal acceleration force to the cuttings to improve liquid separation from the cuttings. The cuttings dryer can help save money on expensive drilling fluids by returning the expensive liquid phase in the mud system through further purification. The KOSUN drilling cuttings treatment system recovers beneficial mud and returns it to the in-service mud system. The KOSUN drilling cuttings treatment system works well for diesel, mineral oil, and synthetic oil-based mud. The KOSUN drilling cuttings treatment system has a higher mud value, and the vertical centrifuge is a more critical piece of equipment in the KOSUN mud treatment system, which also makes the vertical centrifuge more attractive from an economic and practical point of view. In addition, the vertical centrifuge reduces the amount of waste and disposal costs incurred at the rig site.

06/11/202406/11/2024

Find top-quality vertical cuttings dryer for efficient waste management.

In the oil and gas industry, effective waste management is critical to maintaining environmental sustainability and operational efficiency. A key component of this process is the use of a high-quality vertical cuttings dryer. These innovative machines are designed to effectively separate drilling waste from drilling fluids, thereby recovering valuable resources and properly disposing of waste materials.

When looking for the best vertical cuttings dryer for your waste management needs, there are several factors to consider. First and foremost, it is crucial to find a dryer that offers high performance and reliability. This means choosing a machine that can withstand the rigors of drilling operations and consistently deliver efficient results.

Additionally, a high-quality vertical cuttings dryer should be equipped with advanced features to enhance its functionality. This may include adjustable screen basket angles, variable speed controls, and automated systems for monitoring and controlling the drying process. These features not only improve the dryer’s overall performance but also help increase operational flexibility and ease of use.

It is also important to choose a vertical cuttings dryer from a reputable manufacturer with a good track record in the industry. By choosing a machine from a trusted supplier, you can be confident in its quality, durability and long-term performance. Additionally, working with a reliable manufacturer ensures comprehensive technical support and maintenance services, further increasing the efficiency and reliability of your waste management process.

In summary, finding a quality vertical cuttings dryer is crucial for efficient waste management in the oil and gas industry. By prioritizing a manufacturer’s performance, advanced features and reputation, companies can ensure they invest in a dryer that meets their specific needs and delivers consistent, reliable results. With the right equipment, organizations can effectively manage drilling waste, minimize environmental impact, and optimize overall operational efficiency.

Drilling Waste Management: Solving Company’s Environmental and Regulatory Challenges

Drilling waste management is a critical aspect of the oil and gas industry, as it addresses the environmental and regulatory challenges that companies face during drilling operations. The process of drilling for oil and gas generates a significant amount of waste, including drilling mud, cuttings, and other by-products that must be managed and disposed of properly to mitigate environmental impact and comply with regulations.

One of the primary problems that drilling waste management solves for companies is the management of hazardous materials. Drilling waste often contains harmful substances such as heavy metals, hydrocarbons, and other contaminants that can pose serious risks to the environment if not handled appropriately. By implementing effective waste disposal practices, companies can prevent these hazardous materials from polluting soil, water, and air, thus safeguarding the surrounding ecosystems and communities.

Furthermore, proper drilling waste management helps companies adhere to strict environmental regulations and avoid potential legal repercussions. Regulatory bodies impose stringent guidelines on the handling and disposal of drilling waste to protect the environment and public health. Failure to comply with these regulations can result in fines, legal disputes, and damage to the company’s reputation. By investing in efficient waste disposal methods, companies can demonstrate their commitment to environmental stewardship and ensure compliance with the law.

In addition, effective drilling waste disposal contributes to sustainable operations and corporate social responsibility. By minimizing the environmental impact of drilling activities, companies can enhance their reputation and build trust with stakeholders, including local communities, investors, and regulatory authorities. Sustainable waste management practices also align with the growing demand for environmentally responsible business operations, positioning companies as responsible industry leaders.

Overall, drilling waste disposal plays a crucial role in addressing environmental and regulatory challenges for companies in the oil and gas sector. By implementing proper waste management strategies, companies can mitigate environmental risks, comply with regulations, and demonstrate their commitment to sustainability and corporate responsibility. As the industry continues to evolve, investing in innovative and sustainable waste disposal solutions will be essential for companies to thrive in a competitive and environmentally conscious market.

KOSUN- China Solids Control Leader&Drilling Waste Management Expert
Email: sales2@adkosun.com
WhatsApp/Wechat:+86 13379250593
Contact person: Monica Li
Online consulting:
http://www.kosun.com
http://www.kosuneco.com

04/15/202404/15/2024

DRILLING RIG MUD SYSTEM OF KOSUN FOR SALE

The composition of a drilling rig mud system usually includes several key components. These equipment may include shale shakers, desanders, desliters, decanters and slurry tanks. Shale shaker screens are the first line of defense, removing large particles from the mud. Desanders and desilters then further refine the slurry by removing finer solids. Decanter centrifuges are used for the final separation of solid and liquid phases. Mud tanks are used to store and circulate mud throughout the purification process.

Each component of the drilling rig mud system has a specific division of labor. For example, vibrating screens are responsible for the initial separation of large particles, while desanders and deslimers focus on removing finer solids. Decanters then perform final separation, producing clean slurry and water. Mud tanks play a vital role in storing and circulating mud throughout the purification process, ensuring continuous and efficient operation.

In addition to mechanical components, the division of labor in a drilling rig mud system also involves the use of chemical additives. These additives can include flocculants and coagulants, which help enhance the separation of solid and liquid phases. By working in conjunction with mechanical components, these chemical additives play a vital role in the overall efficiency of the system.

In short, the composition and division of labor of a drilling rig mud system are crucial to its effective operation. From mud shale shakers to decanter centrifuges, each component plays a specific role in removing impurities from mud. In addition, the use of chemical additives further increases the efficiency of the system. By understanding the division of labor within the system, industries can ensure the proper functioning of drilling rig mud system, thereby improving environmental and operational outcomes.

mud treatment equipment, drilling mud system, mud treatment system, mud recycling system

03/21/202403/21/2024

What are the treatment methods of oil based drilling cuttings?

Oil-based drilling cuttings refer to the solid waste generated by the contact between drilling fluid and formation rock in the process of oil drilling. Oil-based drilling fluid is a petroleum-based drilling fluid system used to cool drill bits, lubricate and suspend drilling cuttings while forming and maintaining formation stability during drilling. Because the drilling fluid is in contact with the formation, it carries formation rock debris, which is returned to the surface with the drilling fluid to form drilling cuttings.

The primary goal of treating oil-based drilling cuttings is to efficiently separate and recover drilling fluids for reuse while reducing negative environmental impacts.

After the initial recycling, the remaining solid cuttings are treated in the following ways:

Heat treatment: The cuttings are heat treated to remove residual drilling fluids and other contaminants. This can be achieved by pyrolysis, calcination or thermal desorption.

Chemical treatment: Cuttings are treated with chemicals to reduce the impact on the environment. For example, surfactants and solvents are used to clean the cuttings surface to remove grease and contaminants.

Curing/curing: The cuttings are mixed with the curing agent to form a strong solid block. This method can reduce the release of soluble substances in the cuttings and reduce the risk of pollution to the environment.

03/14/202403/14/2024

The liquid-gas separator is an important safety equipment in the oil drilling process

The liquid-gas separator is an important safety equipment in the oil drilling process. It plays a vital role in separating the liquid and gas components extracted from the well. This equipment is critical to maintaining the safety and efficiency of drilling operations.

During oil drilling, large amounts of gas and liquid are brought to the surface along with the crude oil. Liquid-gas separators are designed to separate these components, ensuring that gases are safely vented or captured while liquids are directed to appropriate storage or processing facilities.

One of the primary functions of a liquid-gas separator is to prevent the release of potentially dangerous gases into the atmosphere. By separating gases from liquids, separators help minimize the risk of gas leaks and emissions, causing serious safety and environmental hazards.

In addition to safety benefits, liquid-gas separators play a key role in optimizing the efficiency of the oil drilling process. By separating gas and liquid components, separators can more accurately measure and control production flows. This in turn helps maximize the recovery of valuable resources while minimizing waste and inefficiencies.

Liquid-gas separator designs can vary based on the specific requirements of the drilling operation. However, most separators consist of a container or tank equipped with internal components such as baffles, mist eliminators, and mist eliminators. These components work together to effectively separate the gas and liquid phases, ensuring each component is properly handled and processed.

In general, the liquid-gas separator is an indispensable equipment in the oil drilling process. Its ability to safely and effectively separate gas and liquid components makes it an important tool in ensuring the safety, environmental responsibility and productivity of oil drilling operations. Therefore, oil drilling companies must invest in high-quality liquid-gas separators and ensure they are properly maintained and operated for optimal performance.

02/26/202402/26/2024

KOSUN– one of the Top -Ten drilling cuttings management system companies in China

Are you looking for a reliable drilling waste disposal solution that ticks all the boxes of efficiency and environmental responsibility? Look no further! KOSUN, one of China’s Top -Ten drilling waste disposal companies, Has got you covered. Dive into this blog post to discover how KOSUN’s cutting-edge drilling cuttings management system is revolutionizing the industry with its innovative technology and sustainable practices. Let’s explore together!

The KOSUN drilling cuttings Management system includes which devices：

The KOSUN drilling cuttings management system comprises a range of top-notch devices designed to streamline the waste disposal process. At its core is the Vertical Cuttings Dryer, which effectively separates drilling fluids from cuttings, reducing environmental impact.

Accompanying this is the Hi-G Dryer Shaker, a high-speed vibrating device that further removes solids from liquids for enhanced efficiency.

Additionally, the Decanter Centrifuge plays a crucial role in separating fine solids from fluids through centrifugal force, ensuring thorough waste treatment.

To complement these devices, KOSUN’s Screw Conveyor efficiently transports processed materials for seamless disposal or recycling.

By integrating these advanced devices into their system, KOSUN sets a new standard for effective and eco-friendly drilling cuttings management solutions in the industry.

How do the equipment in the drilling cuttings management system work together?

The equipment in the drilling cuttings management system works together seamlessly to ensure efficient and environmentally friendly waste disposal.
The shale shaker plays a crucial role by separating solids from liquids, allowing for further processing.
Next, the decanter centrifuge comes into play, spinning at high speeds to remove fine particles from the liquid phase.
Simultaneously, the vertical cuttings dryer helps reduce oil content in solids before they are transported off-site for disposal.
Moreover, thermal desorption units are utilized to treat oily sludge and recover valuable resources for reuse.
Each piece of equipment complements one another in this sophisticated system, contributing to safer operations and reduced environmental impact.

Tags： rilling cuttings management system, drilling waste disposal, Cuttings Waste Mud Treatment, Water-Based Waste Mud Equipment, Drilling Waste Treatment Equipment, Oil-Based Mud Cuttings Treatment

02/26/202402/26/2024

The role of oil solids control centrifuge in the drilling industry

Explore the role of oil solid control centrifuge in the oil drilling industry.

In the oil and gas drilling industry, solids control equipment plays a vital role in ensuring the efficiency and safety of the drilling process. One of the key pieces of equipment in a solids control system is the centrifuge. Oil solids control centrifuges are specifically designed to separate solids from drilling fluids, also known as mud, to maintain the required properties of the mud and prevent environmental pollution.

The working principle of a centrifuge is to use centrifugal force to separate solids from liquids. When drilling fluid enters the centrifuge, it spins at high speed, causing solids to be forced to the centrifuge walls while cleaning fluid is discharged through the top. This process continuously removes solids from the drilling fluid, ensuring that the drilling fluid remains in optimal condition for efficient drilling operations.

The petroleum industry uses different types of centrifuges, including decanters and vertical cuttings dryers. Decanters are typically used to remove fine solids from drilling fluids, while vertical cuttings dryers are designed to separate solids from drilling waste cuttings produced during the drilling process.

The importance of oil solids control centrifuges in the drilling process cannot be overstated. Without effective solids control, drilling fluids can become contaminated with solids, resulting in reduced drilling efficiency and potential damage to drilling equipment. Additionally, improper management of drilling waste can lead to environmental contamination, resulting in costly cleanup efforts and potential legal consequences.

In summary, oil solids control centrifuges are critical to maintaining the integrity of drilling fluids and ensuring the success of drilling operations. By effectively separating solids from drilling fluids, centrifuges play a key role in optimizing drilling efficiency and minimizing environmental impact. As technology continues to advance, the development of more efficient and effective centrifuge systems will further enhance the role of solids control equipment in the petroleum industry.

Tags: Oil solid control centrifuge, Drilling fluid centrifuge, solids control centrifuges, centrifuges in drilling

12/13/202312/13/2023

The Requirements for Solidification Treatment of Drilling Waste Mud

The mud, rock cuttings, polluted oil, and oil sludge generated during the process of petroleum and natural gas development have been classified by the country as hazardous waste. Article 55 of the “Law of the People’s Republic of China on the Prevention and Control of Environmental Pollution by Solid Waste” stipulates that units generating hazardous waste must dispose of it in accordance with relevant national regulations and are prohibited from unauthorized dumping or stacking. Article 57, paragraph three, prohibits the provision or commissioning of hazardous waste collection, storage, utilization, and disposal activities to units without an operating permit.
The current situation of the technical treatment of drilling waste mud: The objectives of drilling waste mud treatment are to eliminate pollution and protect the environment, as well as to recycle and utilize it for beneficial purposes.
Xi’an KOSUN primarily utilizes solidification technology for the harmless treatment of drilling waste mud, which is currently a successful technology.
The solidification treatment process for drilling waste mud mainly uses solid control equipment for the solid phase control and solid-liquid separation of drilling fluid during the drilling process to ensure stable performance of the drilling fluid and achieve the repeated circulation and reuse of the mud. The solid control system usually consists of 3-7 mud tanks, equipped with solid control, chemical mixing, and weighting equipment to meet the requirements of different well depths and drilling mud. Each processing equipment can operate independently or in combination and is suitable for drilling projects with depths ranging from 500 to 9000 meters, and it can support the production of mud circulation systems for workover rigs with capacities such as 250HP, 350HP, 450HP, 550HP, 650HP, 750HP, as well as land-based drilling rigs with capacities of 1000HP, 1500HP, 2000HP, and 3000HP.

Tag: Treatment of Drilling Waste Mud